| 提示訊息 | 說明 |
| Drive A error | 磁碟機 A 錯誤 |
| System halt | 系統掛起 |
| Keyboard controller error | 鍵盤控制器錯誤 |
| Keyboard error or no keyboard present | 鍵盤錯誤或不存在 |
| BIOS ROM checksum error | BIOS ROM 校驗錯誤 |
| Single hardisk cable fail | 硬碟 Cable Select 模式下安裝位置不正確 |
| FDD Controller Failure | BIOS 軟碟控制器錯誤 |
| HDD Controller Failure | BIOS 硬碟控制器錯誤 |
| Driver Error | 驅動器錯誤 |
| Cache Memory Bad, Do not Enable Cache | 快取記憶體損壞,不可啟用 |
| Error: Unable to control A20 line | 無法控制 A20 位址線 |
| Memory write/Read failure | 記憶體讀寫失敗 |
| Memory allocation error | 記憶體定位錯誤 |
| CMOS Battery state Low | CMOS 電池沒電 |
| Keyboard interface error | 鍵盤介面錯誤 |
| Hard disk drive failure | 載入硬碟失敗 |
| Hard disk not present | 硬碟不存在 |
| Floppy disk(s) fail (40) | 軟碟機載入失敗(資料線插反/電源線未接/CMOS 設定錯) |
| CMOS checksum error - Defaults loaded | CMOS 校驗錯誤,載入預設值 |
| 提示訊息 | 說明 |
| Insert diskette for drive and press any key when ready | 插入磁碟到驅動器按任意鍵 |
| Your program caused a divide overflow error... | 程式導致溢位錯誤,持續存在聯繫供應商 |
| Windows has disabled direct disk access to protect your long filenames | Windows 禁止直接磁碟存取保護長檔名 |
| The system has been halted. Press Ctrl Alt Del to restart | 系統掛起,按 Ctrl+Alt+Del 重啟 |
| You started your computer with a version of MS-DOS incompatible with this version of Windows... | MS-DOS 版本與 Windows 不相容,插入匹配系統盤重啟 |
| This version of Windows requires a 386 or better processor | 需 386 以上 CPU |
| A20 hardware error. Contact technical support... | A20 位址線硬體錯誤,聯繫技術支援 |
| Starting Windows 98... | 正在啟動 Windows 98 |
| There is an unrecognized command in your CONFIG.SYS file | CONFIG.SYS 有無法識別指令 |
| The following command in your CONFIG.SYS file is incorrect: | CONFIG.SYS 有錯誤指令 |
| The sector size specified in this file is too large | 指定扇區過大 |
| The following file is missing or corrupted: WIN.COM COMMAND.COM | 遺失/損壞:WIN.COM、COMMAND.COM |
| There is an invalid country code or code page in your CONFIG.SYS file | CONFIG.SYS 有無效國家代碼/代碼頁 |
| There is an error in the COUNTRY command in your CONFIG.SYS file | CONFIG.SYS 國家指令錯誤 |
| There is not enough memory for the COUNTRY.SYS file | 記憶體不足載入 COUNTRY.SYS |
| Remove some drivers from your CONFIG.SYS file, and then try again | 移除 CONFIG.SYS 部分驅動再試 |
| The configuration specified in your CONFIG.SYS file is too large for memory | 調整 CONFIG.SYS 獲取足夠記憶體 |
| You have too many block devices specified in your CONFIG.SYS file | 調整 CONFIG.SYS 獲取區塊裝置 |
| The STACKS setting(s) in your CONFIG.SYS file are incorrect | CONFIG.SYS 堆疊設定不正確 |
| Default stack settings will be used instead | 將使用預設堆疊設定 |
| There is an error in your CONFIG.SYS file on line XX | CONFIG.SYS 第 XX 行錯誤 |
| Warning: Logical drives past Z exist and will be ignored | 警告:邏輯磁碟機超過 Z 將被忽略 |
| Type the name of the Command Interpreter (e.g., C:\WINDOWS\COMMAND.COM) Press any key to continue... | 輸入命令解譯器檔名(如 C:\WINDOWS\COMMAND.COM)按任意鍵繼續 |
| Windows is bypassing your startup files. Minimal network support will be loaded if available | Windows 跳過啟動檔,可用時載入最小網路支援 |
| Windows is starting the command prompt only | Windows 僅啟動命令提示字元模式 |
| Windows will prompt you to confirm each startup command | Windows 將提示確認每個啟動指令 |
| The compression driver cannot be set up correctly | 壓縮驅動程式無法正確設置 |
| Get a version from your vendor that is compatible with this version of Windows | 從供應商獲取相容版本 |
| Process the system registry | 執行系統登錄檔 |
| Create a startup log file (BOOTLOG.TXT) | 建立啟動日誌 BOOTLOG.TXT |
| Process your startup device drivers (CONFIG.SYS) | 執行 CONFIG.SYS 裝置驅動 |
| Process your startup command file (AUTOEXEC.BAT) | 執行 AUTOEXEC.BAT 啟動指令 |
| Load the Windows graphical user interface | 載入 Windows 圖形使用者介面 |
| Warning: Windows has detected a registry/configuration error. Choose Command prompt only, and run SCANREG | 偵測到登錄檔/設定錯誤,選擇 DOS 模式執行 SCANREG |
| Warning: Windows has detected a compressed drive access error. Choose Safe mode command prompt only... | 偵測到壓縮磁碟存取錯誤,選擇安全模式命令提示字元協助識別 |